Imported revision

You are reading an older revision. This is not the current page.

Tutorial

Rubydesic · Imported from the former Valkyrien Skies wiki · 7 years ago · Sep 2, 2019, 5:33 PM UTC

c4d309ce-9036-4f60-b7ba-a19ddd21e2bc · MediaWiki wikitext source

Revision 1336 of the former Valkyrien Skies wiki, licensed under Creative Commons Attribution-ShareAlike 4.0 International (CC BY-SA 4.0). Its original wikitext is shown as source only and can't be restored.

MediaWiki wikitext source

'''Think the tutorial could be better? [[Tutorial|Edit it on the wiki!]]''' <!-- Do not delete! This link here is for visitors of the page through the book inside of the game. (to be added) -->

''This tutorial was made by paufg#8578 on Discord and transcribed to the wiki. Thanks!''

== New Control Scheme ==

=== Set up vertical movement. ===
1 - Place ethereum compressors on each corner of your "ship" Build them by placing a 2x2x2 cube of ethereum compressor panels and right-clicking them with a VW wrench
[[File:Four ether compressors non multiblock.png|none|thumb|314x314px|Four ether compressors that have not been converted yet]]
[[File:Ethereum compressor multiblock.png|none|thumb|317x317px|An ethereum compressor multiblock]]
2 - Connect all of them to a lift lever using network relays and wire. Infuse it with physics and your ship is ready to go up and down
[[File:Four ether compressors multiblock.png|none|thumb|320x320px|Four converted ether compressors connected with relay wire]]
<br />

=== Set up Forward and Backwards Movement ===
1 - Build the ethereum engine

Do it by placing ethereum engine parts in a 2x2x3 structure and right-clicking the the middle bottom block of one side with the wrench
[[File:Ethereum engine parts 2x2x3.png|none|thumb|Ethereum engine parts not converted]]
[[File:Converted ethereum engine.png|none|thumb|Converted ethereum engine]]
[[File:Ethereum engine axle.png|none|thumb|Ethereum engine axle ]]
Place a gear box there
[[File:Ethereum engine with gearbox.png|none|thumb|Ethereum engine with gearbox]]
Basically the gearbox has 1 input and 5 outputs. Each of the 5 outputs will always rotate at the same speed no matter what. They rotate with angular velocity proportional to that of the input side. The value of that proportion is 1 by default, but can be -4, -2, -1, 0, 1, 2, or 4. That value is controlled by the chadburn. Using the wrench sets a side to be the input

2 - Place gigantic propeller parts in a square than can be from 3x3 from 7x7 with the one in the middle touching the gear box
[[File:Unconverted propellors.png|none|thumb|Unconverted propellers]]
Right-click the one in the middle with the wrench to build it
[[File:3x3 propeller multiblock.png|none|thumb|3x3 propeller multiblock]]
And your ship should start moving. To control the speed connect the gear box to a speed telegraph using relays and wires
[[File:Ship example with speed telegraph.png|none|thumb|Ship example with speed telegraph]]

=== Set up the ship rotation ===
1 - Place rudders. Note: use stabilizers to keep your ship straight on
[[File:Stablizers on the bottom of ship.png|none|thumb|Stablizers on the bottom of ship]]
Build the rudders by placing pillars made from rudder axles that can be from 2 to 6 blocks high (the can go over or under your ship but they must be in vertical position in order to rotate your ship)
[[File:Rudder axles unconverted .png|none|thumb|Rudder axles unconverted ]]
You know what to do
[[File:Rudder axle with wrench in foreground.png|none|thumb|Click with the wrench]]
2 - Connect them to a ship helm (wires can go through solid blocks)
[[File:Finished tutorial ship.png|none|thumb|Finished tutorial ship]]
<br />