Imported revision

You are reading an older revision. This is not the current page.

Darth Dan moved page [[Tutorial]] to [[Tutorial (VS1)]]: To protect the contents from being overwritten if a newer tutorial gets published

Darth Dan · Imported from the former Valkyrien Skies wiki · minor edit · 3 years ago · Mar 27, 2023, 2:12 PM UTC

3b5464f7-6bac-43a0-8d82-84bf4562d505 · MediaWiki wikitext source

Revision 1736 of the former Valkyrien Skies wiki, licensed under Creative Commons Attribution-ShareAlike 4.0 International (CC BY-SA 4.0). Its original wikitext is shown as source only and can't be restored.

MediaWiki wikitext source

'''Think the tutorial could be better? [[Tutorial|Edit it on the wiki!]]''' <!-- Do not delete! This link here is for visitors of the page through the book inside of the game. (to be added) -->

''This tutorial was made by '''paufg#8578''' on Discord and transcribed to the wiki. Thanks!''

'''''Please keep in mind some terminology may be a bit outdated. Ethereum = Valkyrium.'''''

== Prerequisites ==

Make sure you have Minecraft {{ModLoader}} {{ModMinecraftVersion}} and the latest version of {{ModName}} in your .minecraft/mods folder.

== New Control Scheme ==

=== Set up Vertical movement ===
1 - Place [[Valkyrium Compressor|Valkyrium Compressors]] on each corner of your "ship" Build them by placing a 2x2x2 cube of [[Valkyrium Compressor Part|Valkyrium Compressor parts]] and right-clicking them with a [[VS Wrench]].
[[File:Four ether compressors non multiblock.png|none|thumb|314x314px|Four Valkyrium Compressors that have not been constructed yet]]
[[File:Ethereum compressor multiblock.png|none|thumb|317x317px|A Valkyrium Compressor multiblock]]
2 - Connect all of them to a lift lever using a [[Network Relay]] and 5 [[Relay Wire|wires]]. Infuse it with physics and your ship is ready to go up and down!
[[File:Four ether compressors multiblock.png|none|thumb|320x320px|Four constructed Valkyrium Compressors connected with Relay Wire]]


=== Set up Forward and Backwards Movement ===
1 - Build the [[Valkyrium Engine]].

Do it by placing [[Valkyrium Engine Part|Valkyrium Engine parts]] in a 2x2x3 structure and right-clicking the the middle bottom block of one side with the wrench.
[[File:Ethereum engine parts 2x2x3.png|none|thumb|Valkyrium Engine parts not constructed]]
[[File:Converted ethereum engine.png|none|thumb|Constructed Valkyrium Engine]]
[[File:Ethereum engine axle.png|none|thumb|Valkyrium Engine axle]]
Place a [[Gearbox]] there.
[[File:Ethereum engine with gearbox.png|none|thumb|Valkyrium Engine with Gearbox]]
Basically the gearbox has 1 input and 5 outputs. Each of the 5 outputs will always rotate at the same speed no matter what. They rotate with angular velocity proportional to that of the input side. The value of that proportion is 1 by default, but can be -4, -2, -1, 0, 1, 2, or 4. That value is controlled by the [[Speed Telegraph]]. Using the wrench sets a side to be the input.

2 - Place [[Giant Propeller Part|Giant Propeller parts]] in a square that can be from 3x3 from 7x7 with the one in the middle touching the Gearbox.
[[File:Unconverted propellors.png|none|thumb|Unconstructed propellers]]
Right-click the one in the middle with a Wrench to construct it.
[[File:3x3 propeller multiblock.png|none|thumb|3x3 propeller multiblock]]
And your ship should start moving. To control the speed connect the Gearbox to a Speed Telegraph using Relays and Wires.
[[File:Ship example with speed telegraph.png|none|thumb|Ship example with a Speed Telegraph]]

=== Set up the ship rotation ===
1 - Place [[Rudder|Rudders]]. Note: use [[Gyro Stabilizers]] to keep your ship straight up.
[[File:Stablizers on the bottom of ship.png|none|thumb|Stablizers on the bottom of ship]]
Build the Rudders by placing pillars made from [[Rudder Axle|Rudder Axles]] that can be from 2 to 6 blocks high (the can go over or under your ship but they must be in a vertical position in order to rotate your ship)
[[File:Rudder axles unconverted.png|none|thumb|Rudder axles unconstructed]]
You know what to do...
[[File:Rudder axle with wrench in foreground.png|none|thumb|Click with the Wrench]]
2 - Connect them to a [[Ship Helm]] (''wires can go through solid blocks'')
[[File:Finished tutorial ship.png|none|thumb|Finished tutorial ship]]

[[Category:WIP]]